Laboratory model tests on laterally loaded piles in plastic clay

Y. E.A. Mohamedzein, F. A.E. Nour Eldaim, A. B. Abdelwahab

Research output: Contribution to journalArticle

3 Citations (Scopus)

Abstract

This paper presents the results of laboratory model tests conducted to study the behavior of laterally loaded piles installed in plastic clay. The effects of different factors such as pile dimensions, pile material and method of installation were studied. The pile response is presented in terms of load-deflection curves, bending moment distribution, and the p-y curves. The load-deflection curves are generally non-linear specially for large length/diameter (L/d) ratios and large diameters. The ultimate lateral pile capacity increases with the increase in L/d ratio and the pile diameter. The maximum bending moment increases with the increase in L/d ratio and the pile diameter. The maximum bending moment occurs at a depth varying from 0·13L to 0·32L. The bending stresses at the ultimate load are much less than the yielding stress of steel and the flexural strength of concrete. This implies that the deflection controls the design of laterally loaded piles in plastic clays. The experimental p-y curves are different from the existing p-y curves for piles with small diameters and are approximately similar to the existing p-y curves for piles with larger diameters. The bored method of installation gives greater ultimate soil resistance than the preinstalled method for both concrete and steel piles. Overall this study showed that the laboratory model tests with relatively large diameter (>30 mm) can be used to give insight into the performance of laterally loaded piles installed in plastic clays.

Original languageEnglish
Pages (from-to)241-250
Number of pages10
JournalInternational Journal of Geotechnical Engineering
Volume7
Issue number3
DOIs
Publication statusPublished - Jul 1 2013

Fingerprint

model test
Piles
Clay
pile
plastics
plastic
clay
Plastics
testing
deflection
Bending moments
steel
laboratory
pile response
Concretes
Steel
methodology
Bending strength
Loads (forces)

Keywords

  • Bending moment
  • Deflection
  • Laboratory model
  • Laterally loaded piles
  • P-y curves
  • Plastic clay

ASJC Scopus subject areas

  • Environmental Engineering
  • Geotechnical Engineering and Engineering Geology
  • Soil Science

Cite this

Laboratory model tests on laterally loaded piles in plastic clay. / Mohamedzein, Y. E.A.; Nour Eldaim, F. A.E.; Abdelwahab, A. B.

In: International Journal of Geotechnical Engineering, Vol. 7, No. 3, 01.07.2013, p. 241-250.

Research output: Contribution to journalArticle

@article{3167703a9d3a4bb2aed0fcbc7cf65011,
title = "Laboratory model tests on laterally loaded piles in plastic clay",
abstract = "This paper presents the results of laboratory model tests conducted to study the behavior of laterally loaded piles installed in plastic clay. The effects of different factors such as pile dimensions, pile material and method of installation were studied. The pile response is presented in terms of load-deflection curves, bending moment distribution, and the p-y curves. The load-deflection curves are generally non-linear specially for large length/diameter (L/d) ratios and large diameters. The ultimate lateral pile capacity increases with the increase in L/d ratio and the pile diameter. The maximum bending moment increases with the increase in L/d ratio and the pile diameter. The maximum bending moment occurs at a depth varying from 0·13L to 0·32L. The bending stresses at the ultimate load are much less than the yielding stress of steel and the flexural strength of concrete. This implies that the deflection controls the design of laterally loaded piles in plastic clays. The experimental p-y curves are different from the existing p-y curves for piles with small diameters and are approximately similar to the existing p-y curves for piles with larger diameters. The bored method of installation gives greater ultimate soil resistance than the preinstalled method for both concrete and steel piles. Overall this study showed that the laboratory model tests with relatively large diameter (>30 mm) can be used to give insight into the performance of laterally loaded piles installed in plastic clays.",
keywords = "Bending moment, Deflection, Laboratory model, Laterally loaded piles, P-y curves, Plastic clay",
author = "Mohamedzein, {Y. E.A.} and {Nour Eldaim}, {F. A.E.} and Abdelwahab, {A. B.}",
year = "2013",
month = "7",
day = "1",
doi = "10.1179/1938636213Z.00000000030",
language = "English",
volume = "7",
pages = "241--250",
journal = "International Journal of Geotechnical Engineering",
issn = "1938-6362",
publisher = "Maney Publishing",
number = "3",

}

TY - JOUR

T1 - Laboratory model tests on laterally loaded piles in plastic clay

AU - Mohamedzein, Y. E.A.

AU - Nour Eldaim, F. A.E.

AU - Abdelwahab, A. B.

PY - 2013/7/1

Y1 - 2013/7/1

N2 - This paper presents the results of laboratory model tests conducted to study the behavior of laterally loaded piles installed in plastic clay. The effects of different factors such as pile dimensions, pile material and method of installation were studied. The pile response is presented in terms of load-deflection curves, bending moment distribution, and the p-y curves. The load-deflection curves are generally non-linear specially for large length/diameter (L/d) ratios and large diameters. The ultimate lateral pile capacity increases with the increase in L/d ratio and the pile diameter. The maximum bending moment increases with the increase in L/d ratio and the pile diameter. The maximum bending moment occurs at a depth varying from 0·13L to 0·32L. The bending stresses at the ultimate load are much less than the yielding stress of steel and the flexural strength of concrete. This implies that the deflection controls the design of laterally loaded piles in plastic clays. The experimental p-y curves are different from the existing p-y curves for piles with small diameters and are approximately similar to the existing p-y curves for piles with larger diameters. The bored method of installation gives greater ultimate soil resistance than the preinstalled method for both concrete and steel piles. Overall this study showed that the laboratory model tests with relatively large diameter (>30 mm) can be used to give insight into the performance of laterally loaded piles installed in plastic clays.

AB - This paper presents the results of laboratory model tests conducted to study the behavior of laterally loaded piles installed in plastic clay. The effects of different factors such as pile dimensions, pile material and method of installation were studied. The pile response is presented in terms of load-deflection curves, bending moment distribution, and the p-y curves. The load-deflection curves are generally non-linear specially for large length/diameter (L/d) ratios and large diameters. The ultimate lateral pile capacity increases with the increase in L/d ratio and the pile diameter. The maximum bending moment increases with the increase in L/d ratio and the pile diameter. The maximum bending moment occurs at a depth varying from 0·13L to 0·32L. The bending stresses at the ultimate load are much less than the yielding stress of steel and the flexural strength of concrete. This implies that the deflection controls the design of laterally loaded piles in plastic clays. The experimental p-y curves are different from the existing p-y curves for piles with small diameters and are approximately similar to the existing p-y curves for piles with larger diameters. The bored method of installation gives greater ultimate soil resistance than the preinstalled method for both concrete and steel piles. Overall this study showed that the laboratory model tests with relatively large diameter (>30 mm) can be used to give insight into the performance of laterally loaded piles installed in plastic clays.

KW - Bending moment

KW - Deflection

KW - Laboratory model

KW - Laterally loaded piles

KW - P-y curves

KW - Plastic clay

UR - http://www.scopus.com/inward/record.url?scp=84922692798&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84922692798&partnerID=8YFLogxK

U2 - 10.1179/1938636213Z.00000000030

DO - 10.1179/1938636213Z.00000000030

M3 - Article

AN - SCOPUS:84922692798

VL - 7

SP - 241

EP - 250

JO - International Journal of Geotechnical Engineering

JF - International Journal of Geotechnical Engineering

SN - 1938-6362

IS - 3

ER -