The influence of high permeability lenses on immiscible, first- and multi-contact miscible gas injection

Yahya M. Al-Wahaibi, Abdullah K. Al-Hadrami

Research output: Contribution to journalArticle

5 Citations (Scopus)

Abstract

The recovery of oil by injection of miscible gas has been a subject of interest and research in petroleum engineering over the past 40. years. In a first contact miscible displacement, the injected fluid forms only single-phase mixtures with oil in place, so in theory, 100% recovery can be achieved. Unfortunately, many phenomena conspire to limit the efficiency of the miscible flooding process including viscous fingering and permeability heterogeneity. One type of important heterogeneities that occur at the small scale is the lensed system. This is one of the most common sedimentary structures found in sandstone reservoirs and is almost universal.This paper investigates the physics of gas-oil multi-contact miscible (MCM) displacements within lensed porous media using a combination of well-characterised laboratory experiments and detailed numerical simulation. The aims were to:. (1)quantify the recovery efficiency of MCM displacements conducted at different flow conditions,(2)provide a set of benchmark experimental data for MCM displacements performed within lensed porous media, and(3)validate conventional compositional simulation of MCM displacements.The novel experimental studies were conducted in specially designed lens visual models packed with unconsolidated glass beads and used a two-phase three-component (IPA/water/cyclohexene) liquid system that exhibits an upper critical point at ambient conditions. First contact miscible (FCM), immiscible and MCM displacement experiments were performed. They were then simulated using a commercial compositional simulator with a single set of EOS parameters and without using history matching (all input data to the simulator were determined from independent experiments).The produced oil and gas in the experiments were found not to be in compositional equilibrium. This was observed in both homogeneous (as reported previously by Al-Wahaibi et al., 2005) and lens models. This indicates that nonequilibrium occurs at even smaller scales than the lensed structure. As a result, the oil recoveries and gas cuts predicted by compositional simulation for MCM displacements differed significantly from the experimental results, although an excellent match was obtained for the FCM and immiscible displacements.Further experiments investigating the effects of varying injection rates and gravity forces on the level of nonequilibrium observed in the produced fluids are described. Numerical simulation of these experiments provides additional insight into the physical mechanisms causing the nonequilibrium.The experiments performed in this study are the first of their kind as they report the significance of nonequilibrium on MCM process prediction and the influence of lens heterogeneities on MCM injection. This study has important implications for the correct interpretation of core data, and for scale-up processes to reservoir scale, particularly for handling gas/oil nonequilibrium when modelling MCM displacements.

Original languageEnglish
Pages (from-to)313-325
Number of pages13
JournalJournal of Petroleum Science and Engineering
Volume77
Issue number3-4
DOIs
Publication statusPublished - Jun 2011

Fingerprint

Lenses
permeability
gas
oil
Experiments
Recovery
Gas oils
experiment
Porous materials
Simulators
Gases
Petroleum engineering
simulation
simulator
porous medium
Fluids
Computer simulation
petroleum engineering
fingering
Sandstone

Keywords

  • Capillary pressure
  • Contact angle
  • Interfacial tension

ASJC Scopus subject areas

  • Geotechnical Engineering and Engineering Geology
  • Fuel Technology

Cite this

The influence of high permeability lenses on immiscible, first- and multi-contact miscible gas injection. / Al-Wahaibi, Yahya M.; Al-Hadrami, Abdullah K.

In: Journal of Petroleum Science and Engineering, Vol. 77, No. 3-4, 06.2011, p. 313-325.

Research output: Contribution to journalArticle

@article{0eb51ad8844446ba8cf6b57c9e06fd77,
title = "The influence of high permeability lenses on immiscible, first- and multi-contact miscible gas injection",
abstract = "The recovery of oil by injection of miscible gas has been a subject of interest and research in petroleum engineering over the past 40. years. In a first contact miscible displacement, the injected fluid forms only single-phase mixtures with oil in place, so in theory, 100{\%} recovery can be achieved. Unfortunately, many phenomena conspire to limit the efficiency of the miscible flooding process including viscous fingering and permeability heterogeneity. One type of important heterogeneities that occur at the small scale is the lensed system. This is one of the most common sedimentary structures found in sandstone reservoirs and is almost universal.This paper investigates the physics of gas-oil multi-contact miscible (MCM) displacements within lensed porous media using a combination of well-characterised laboratory experiments and detailed numerical simulation. The aims were to:. (1)quantify the recovery efficiency of MCM displacements conducted at different flow conditions,(2)provide a set of benchmark experimental data for MCM displacements performed within lensed porous media, and(3)validate conventional compositional simulation of MCM displacements.The novel experimental studies were conducted in specially designed lens visual models packed with unconsolidated glass beads and used a two-phase three-component (IPA/water/cyclohexene) liquid system that exhibits an upper critical point at ambient conditions. First contact miscible (FCM), immiscible and MCM displacement experiments were performed. They were then simulated using a commercial compositional simulator with a single set of EOS parameters and without using history matching (all input data to the simulator were determined from independent experiments).The produced oil and gas in the experiments were found not to be in compositional equilibrium. This was observed in both homogeneous (as reported previously by Al-Wahaibi et al., 2005) and lens models. This indicates that nonequilibrium occurs at even smaller scales than the lensed structure. As a result, the oil recoveries and gas cuts predicted by compositional simulation for MCM displacements differed significantly from the experimental results, although an excellent match was obtained for the FCM and immiscible displacements.Further experiments investigating the effects of varying injection rates and gravity forces on the level of nonequilibrium observed in the produced fluids are described. Numerical simulation of these experiments provides additional insight into the physical mechanisms causing the nonequilibrium.The experiments performed in this study are the first of their kind as they report the significance of nonequilibrium on MCM process prediction and the influence of lens heterogeneities on MCM injection. This study has important implications for the correct interpretation of core data, and for scale-up processes to reservoir scale, particularly for handling gas/oil nonequilibrium when modelling MCM displacements.",
keywords = "Capillary pressure, Contact angle, Interfacial tension",
author = "Al-Wahaibi, {Yahya M.} and Al-Hadrami, {Abdullah K.}",
year = "2011",
month = "6",
doi = "10.1016/j.petrol.2011.04.005",
language = "English",
volume = "77",
pages = "313--325",
journal = "Journal of Petroleum Science and Engineering",
issn = "0920-4105",
publisher = "Elsevier",
number = "3-4",

}

TY - JOUR

T1 - The influence of high permeability lenses on immiscible, first- and multi-contact miscible gas injection

AU - Al-Wahaibi, Yahya M.

AU - Al-Hadrami, Abdullah K.

PY - 2011/6

Y1 - 2011/6

N2 - The recovery of oil by injection of miscible gas has been a subject of interest and research in petroleum engineering over the past 40. years. In a first contact miscible displacement, the injected fluid forms only single-phase mixtures with oil in place, so in theory, 100% recovery can be achieved. Unfortunately, many phenomena conspire to limit the efficiency of the miscible flooding process including viscous fingering and permeability heterogeneity. One type of important heterogeneities that occur at the small scale is the lensed system. This is one of the most common sedimentary structures found in sandstone reservoirs and is almost universal.This paper investigates the physics of gas-oil multi-contact miscible (MCM) displacements within lensed porous media using a combination of well-characterised laboratory experiments and detailed numerical simulation. The aims were to:. (1)quantify the recovery efficiency of MCM displacements conducted at different flow conditions,(2)provide a set of benchmark experimental data for MCM displacements performed within lensed porous media, and(3)validate conventional compositional simulation of MCM displacements.The novel experimental studies were conducted in specially designed lens visual models packed with unconsolidated glass beads and used a two-phase three-component (IPA/water/cyclohexene) liquid system that exhibits an upper critical point at ambient conditions. First contact miscible (FCM), immiscible and MCM displacement experiments were performed. They were then simulated using a commercial compositional simulator with a single set of EOS parameters and without using history matching (all input data to the simulator were determined from independent experiments).The produced oil and gas in the experiments were found not to be in compositional equilibrium. This was observed in both homogeneous (as reported previously by Al-Wahaibi et al., 2005) and lens models. This indicates that nonequilibrium occurs at even smaller scales than the lensed structure. As a result, the oil recoveries and gas cuts predicted by compositional simulation for MCM displacements differed significantly from the experimental results, although an excellent match was obtained for the FCM and immiscible displacements.Further experiments investigating the effects of varying injection rates and gravity forces on the level of nonequilibrium observed in the produced fluids are described. Numerical simulation of these experiments provides additional insight into the physical mechanisms causing the nonequilibrium.The experiments performed in this study are the first of their kind as they report the significance of nonequilibrium on MCM process prediction and the influence of lens heterogeneities on MCM injection. This study has important implications for the correct interpretation of core data, and for scale-up processes to reservoir scale, particularly for handling gas/oil nonequilibrium when modelling MCM displacements.

AB - The recovery of oil by injection of miscible gas has been a subject of interest and research in petroleum engineering over the past 40. years. In a first contact miscible displacement, the injected fluid forms only single-phase mixtures with oil in place, so in theory, 100% recovery can be achieved. Unfortunately, many phenomena conspire to limit the efficiency of the miscible flooding process including viscous fingering and permeability heterogeneity. One type of important heterogeneities that occur at the small scale is the lensed system. This is one of the most common sedimentary structures found in sandstone reservoirs and is almost universal.This paper investigates the physics of gas-oil multi-contact miscible (MCM) displacements within lensed porous media using a combination of well-characterised laboratory experiments and detailed numerical simulation. The aims were to:. (1)quantify the recovery efficiency of MCM displacements conducted at different flow conditions,(2)provide a set of benchmark experimental data for MCM displacements performed within lensed porous media, and(3)validate conventional compositional simulation of MCM displacements.The novel experimental studies were conducted in specially designed lens visual models packed with unconsolidated glass beads and used a two-phase three-component (IPA/water/cyclohexene) liquid system that exhibits an upper critical point at ambient conditions. First contact miscible (FCM), immiscible and MCM displacement experiments were performed. They were then simulated using a commercial compositional simulator with a single set of EOS parameters and without using history matching (all input data to the simulator were determined from independent experiments).The produced oil and gas in the experiments were found not to be in compositional equilibrium. This was observed in both homogeneous (as reported previously by Al-Wahaibi et al., 2005) and lens models. This indicates that nonequilibrium occurs at even smaller scales than the lensed structure. As a result, the oil recoveries and gas cuts predicted by compositional simulation for MCM displacements differed significantly from the experimental results, although an excellent match was obtained for the FCM and immiscible displacements.Further experiments investigating the effects of varying injection rates and gravity forces on the level of nonequilibrium observed in the produced fluids are described. Numerical simulation of these experiments provides additional insight into the physical mechanisms causing the nonequilibrium.The experiments performed in this study are the first of their kind as they report the significance of nonequilibrium on MCM process prediction and the influence of lens heterogeneities on MCM injection. This study has important implications for the correct interpretation of core data, and for scale-up processes to reservoir scale, particularly for handling gas/oil nonequilibrium when modelling MCM displacements.

KW - Capillary pressure

KW - Contact angle

KW - Interfacial tension

UR - http://www.scopus.com/inward/record.url?scp=79957469587&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=79957469587&partnerID=8YFLogxK

U2 - 10.1016/j.petrol.2011.04.005

DO - 10.1016/j.petrol.2011.04.005

M3 - Article

AN - SCOPUS:79957469587

VL - 77

SP - 313

EP - 325

JO - Journal of Petroleum Science and Engineering

JF - Journal of Petroleum Science and Engineering

SN - 0920-4105

IS - 3-4

ER -