Influence of drag-reducing polymer on flow patterns, drag reduction and slip velocity ratio of oil-water flow in horizontal pipe

Research output: Contribution to journalArticle

17 Citations (Scopus)

Abstract

Experimental investigation of the effects of drag-reducing polymer on oil-water flow patterns, pressure drops, phase inversion and slip ratio in a horizontal acrylic pipe of 30.6-mm ID was carried out. The polymer which is a water-soluble, high-molecular-weight anionic copolymer of polyacrylamide and 2-Acrylamido-2-Methylpropane Sulfonic acid (AMPS) was prepared in 2000. ppm master solution and injected at controlled flow rates to provide 40. ppm of the polymer in the water phase. In the flow conditions of 0.1-1.6. m/s mixture velocity and 0.05-0.9 input oil volume fractions investigated, the addition of the polymer affected the flow characteristics especially at lower mixture velocities and input oil volume fractions. The stratified, dual continuous and dispersed oil in water and water layer flow patterns were extended to higher mixture velocities but the oil-continuous flow patterns were not affected by the addition of the polymer. There were significant reductions in the pressure drops after the addition of the polymer mainly in water-dominated flow regions and these reductions increased with increase in the mixture velocity and decrease in the input oil volume fraction, leading to maximum drag reduction of about 64% at the highest mixture velocity and at 0.05 input oil volume fraction. Again, the addition of the polymer eliminated or shifted the sharp increases in the pressure drops at the phase inversion points towards higher input oil volume fractions. Finally, the addition of the polymer increased the slip velocity ratios especially at lower mixture velocities.

Original languageEnglish
Pages (from-to)1-10
Number of pages10
JournalInternational Journal of Multiphase Flow
Volume73
DOIs
Publication statusPublished - Jul 1 2015

Fingerprint

drag reduction
Drag reduction
water flow
Flow patterns
drag
Drag
flow distribution
Polymers
Oils
slip
oils
Pipe
Water
polymers
Volume fraction
pressure drop
Pressure drop
water
inversions
Sulfonic Acids

Keywords

  • Drag reductions
  • Flow patterns
  • Holdups
  • Oil-water
  • Pressure gradients
  • Slip ratios

ASJC Scopus subject areas

  • Fluid Flow and Transfer Processes
  • Mechanical Engineering
  • Physics and Astronomy(all)

Cite this

@article{3331241f961c461fa8b64dcd60350d65,
title = "Influence of drag-reducing polymer on flow patterns, drag reduction and slip velocity ratio of oil-water flow in horizontal pipe",
abstract = "Experimental investigation of the effects of drag-reducing polymer on oil-water flow patterns, pressure drops, phase inversion and slip ratio in a horizontal acrylic pipe of 30.6-mm ID was carried out. The polymer which is a water-soluble, high-molecular-weight anionic copolymer of polyacrylamide and 2-Acrylamido-2-Methylpropane Sulfonic acid (AMPS) was prepared in 2000. ppm master solution and injected at controlled flow rates to provide 40. ppm of the polymer in the water phase. In the flow conditions of 0.1-1.6. m/s mixture velocity and 0.05-0.9 input oil volume fractions investigated, the addition of the polymer affected the flow characteristics especially at lower mixture velocities and input oil volume fractions. The stratified, dual continuous and dispersed oil in water and water layer flow patterns were extended to higher mixture velocities but the oil-continuous flow patterns were not affected by the addition of the polymer. There were significant reductions in the pressure drops after the addition of the polymer mainly in water-dominated flow regions and these reductions increased with increase in the mixture velocity and decrease in the input oil volume fraction, leading to maximum drag reduction of about 64{\%} at the highest mixture velocity and at 0.05 input oil volume fraction. Again, the addition of the polymer eliminated or shifted the sharp increases in the pressure drops at the phase inversion points towards higher input oil volume fractions. Finally, the addition of the polymer increased the slip velocity ratios especially at lower mixture velocities.",
keywords = "Drag reductions, Flow patterns, Holdups, Oil-water, Pressure gradients, Slip ratios",
author = "A. Abubakar and T. Al-Wahaibi and Al-Hashmi, {A. R.} and Y. Al-Wahaibi and A. Al-Ajmi and M. Eshrati",
year = "2015",
month = "7",
day = "1",
doi = "10.1016/j.ijmultiphaseflow.2015.02.016",
language = "English",
volume = "73",
pages = "1--10",
journal = "International Journal of Multiphase Flow",
issn = "0301-9322",
publisher = "Elsevier BV",

}

TY - JOUR

T1 - Influence of drag-reducing polymer on flow patterns, drag reduction and slip velocity ratio of oil-water flow in horizontal pipe

AU - Abubakar, A.

AU - Al-Wahaibi, T.

AU - Al-Hashmi, A. R.

AU - Al-Wahaibi, Y.

AU - Al-Ajmi, A.

AU - Eshrati, M.

PY - 2015/7/1

Y1 - 2015/7/1

N2 - Experimental investigation of the effects of drag-reducing polymer on oil-water flow patterns, pressure drops, phase inversion and slip ratio in a horizontal acrylic pipe of 30.6-mm ID was carried out. The polymer which is a water-soluble, high-molecular-weight anionic copolymer of polyacrylamide and 2-Acrylamido-2-Methylpropane Sulfonic acid (AMPS) was prepared in 2000. ppm master solution and injected at controlled flow rates to provide 40. ppm of the polymer in the water phase. In the flow conditions of 0.1-1.6. m/s mixture velocity and 0.05-0.9 input oil volume fractions investigated, the addition of the polymer affected the flow characteristics especially at lower mixture velocities and input oil volume fractions. The stratified, dual continuous and dispersed oil in water and water layer flow patterns were extended to higher mixture velocities but the oil-continuous flow patterns were not affected by the addition of the polymer. There were significant reductions in the pressure drops after the addition of the polymer mainly in water-dominated flow regions and these reductions increased with increase in the mixture velocity and decrease in the input oil volume fraction, leading to maximum drag reduction of about 64% at the highest mixture velocity and at 0.05 input oil volume fraction. Again, the addition of the polymer eliminated or shifted the sharp increases in the pressure drops at the phase inversion points towards higher input oil volume fractions. Finally, the addition of the polymer increased the slip velocity ratios especially at lower mixture velocities.

AB - Experimental investigation of the effects of drag-reducing polymer on oil-water flow patterns, pressure drops, phase inversion and slip ratio in a horizontal acrylic pipe of 30.6-mm ID was carried out. The polymer which is a water-soluble, high-molecular-weight anionic copolymer of polyacrylamide and 2-Acrylamido-2-Methylpropane Sulfonic acid (AMPS) was prepared in 2000. ppm master solution and injected at controlled flow rates to provide 40. ppm of the polymer in the water phase. In the flow conditions of 0.1-1.6. m/s mixture velocity and 0.05-0.9 input oil volume fractions investigated, the addition of the polymer affected the flow characteristics especially at lower mixture velocities and input oil volume fractions. The stratified, dual continuous and dispersed oil in water and water layer flow patterns were extended to higher mixture velocities but the oil-continuous flow patterns were not affected by the addition of the polymer. There were significant reductions in the pressure drops after the addition of the polymer mainly in water-dominated flow regions and these reductions increased with increase in the mixture velocity and decrease in the input oil volume fraction, leading to maximum drag reduction of about 64% at the highest mixture velocity and at 0.05 input oil volume fraction. Again, the addition of the polymer eliminated or shifted the sharp increases in the pressure drops at the phase inversion points towards higher input oil volume fractions. Finally, the addition of the polymer increased the slip velocity ratios especially at lower mixture velocities.

KW - Drag reductions

KW - Flow patterns

KW - Holdups

KW - Oil-water

KW - Pressure gradients

KW - Slip ratios

UR - http://www.scopus.com/inward/record.url?scp=84925443421&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84925443421&partnerID=8YFLogxK

U2 - 10.1016/j.ijmultiphaseflow.2015.02.016

DO - 10.1016/j.ijmultiphaseflow.2015.02.016

M3 - Article

VL - 73

SP - 1

EP - 10

JO - International Journal of Multiphase Flow

JF - International Journal of Multiphase Flow

SN - 0301-9322

ER -