• 185 Citations
  • 4 h-Index
20072019
If you made any changes in Pure these will be visible here soon.

Research Output 2007 2019

  • 185 Citations
  • 4 h-Index
  • 10 Article
  • 5 Conference contribution
2019
4 Citations (Scopus)

Production of aluminum alloy-based metal matrix composites using scrap aluminum alloy and waste materials: Influence on microstructure and mechanical properties

Krishnan, P. K., Christy, J. V., Ramanathan, A., Mourad, A. H. I., Muraliraja, R., Al-Maharbi, M., Murali, V. & Chandra, M. M., May 5 2019, In : Journal of Alloys and Compounds. 784, p. 1047-1061 15 p.

Research output: Contribution to journalArticle

Aluminum Oxide
Aluminum alloys
Alumina
Metals
Mechanical properties
2018
4 Citations (Scopus)

An experimental investigation of the effect of defect shape and orientation on the burst pressure of pressurised pipes

Al-Owaisi, S., Becker, A. A., Sun, W., Al Shabibi, A., Al-Maharbi, M., Pervez, T. & Al-Salmi, H., Nov 1 2018, In : Engineering Failure Analysis. 93, p. 200-213 14 p.

Research output: Contribution to journalArticle

Pipe
Defects
Plant shutdowns
Gas industry
Steel pipe
1 Citation (Scopus)
Squeeze casting
Aluminum Oxide
Aluminum
Compressive strength
Alumina
High strength steel
Heat treatment
Steel
Brittle fracture
Tempering
2016
4 Citations (Scopus)

Microstructure evolution of ultra-fine grain low-carbon steel tubular undergoing radial expansion process

Al-Abri, O. S., Pervez, T., Al-Maharbi, M. H. & Khan, R., Jan 27 2016, In : Materials Science and Engineering A. 654, p. 94-106 13 p.

Research output: Contribution to journalArticle

low carbon steels
Low carbon steel
microstructure
Microstructure
expansion
2015

Mechanical and Microstructural changes of fine GRAINED C-Mn steel tubular undergoing down-hole cold expansion process

Al-Abri, O. S., Pervez, T. & Al-Maharbi, M. H., 2015, Mechanics of Solids, Structures and Fluids. American Society of Mechanical Engineers (ASME), Vol. 9-2015.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Steel
Martensite
Mechanical testing
Microstructure
Ferrite
2014

Modeling of twinning based plasticity phenomenon in Austenite dominated steels under combined loading

Khan, R., Al-Abri, O. S., Pervez, T. & Al-Maharbi, M., 2014, ASME International Mechanical Engineering Congress and Exposition, Proceedings (IMECE). American Society of Mechanical Engineers (ASME), Vol. 9.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Twinning
Austenite
Plasticity
Steel
Formability
1 Citation (Scopus)

Prediction of flow stress anisotropy and tension compression asymmetry of hot rolled AZ31B Mg alloy

Al-Maharbi, M. & Karaman, I., 2014, Advanced Materials Research. Trans Tech Publications, Vol. 911. p. 178-184 7 p. (Advanced Materials Research; vol. 911).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Plastic flow
Hardening
Compaction
Anisotropy
Twinning
2011
64 Citations (Scopus)

Grain refinement vs. crystallographic texture: Mechanical anisotropy in a magnesium alloy

Foley, D. C., Al-Maharbi, M., Hartwig, K. T., Karaman, I., Kecskes, L. J. & Mathaudhu, S. N., Jan 2011, In : Scripta Materialia. 64, 2, p. 193-196 4 p.

Research output: Contribution to journalArticle

Dynamic recrystallization
Grain refinement
Twinning
magnesium alloys
twinning
75 Citations (Scopus)

Microstructure, crystallographic texture, and plastic anisotropy evolution in an Mg alloy during equal channel angular extrusion processing

Al-Maharbi, M., Karaman, I., Beyerlein, I. J., Foley, D., Hartwig, K. T., Kecskes, L. J. & Mathaudhu, S. N., Sep 25 2011, In : Materials Science and Engineering A. 528, 25-26, p. 7616-7627 12 p.

Research output: Contribution to journalArticle

plastic anisotropy
Extrusion
Anisotropy
textures
Textures
2010
14 Citations (Scopus)

Flow response of a severe plastically deformed two-phase zinc-aluminum alloy

Al-Maharbi, M., Karaman, I. & Purcek, G., Jan 15 2010, In : Materials Science and Engineering A. 527, 3, p. 518-525 8 p.

Research output: Contribution to journalArticle

zinc alloys
Zinc alloys
aluminum alloys
Extrusion
Aluminum alloys
1 Citation (Scopus)

Importance of crystallographic texture of AZ31B on flow stress anisotropy and tension-compression asymmetry

Al-Maharbi, M., Foley, D., Karaman, I., Beyerlein, I., Hartwig, K. T., Kecskes, L. J. & Mathaudhu, S., 2010, Magnesium Technology. p. 445-450 6 p.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Plastic flow
Extrusion
Anisotropy
Textures
Dynamic recrystallization

Mechanical behavior of AZ31 due to texture and microstructure

Foley, D. C., Al-Maharbi, M., Karaman, I., Hartwig, T., Kecskes, L. J. & Mathaudhu, S., 2010, Magnesium Technology. p. 451-454 4 p.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Textures
Microstructure
Anisotropy
Tensile testing
Processing
2007
17 Citations (Scopus)

Enhancement in mechanical behavior and wear resistance of severe plastically deformed two-phase Zn-Al alloys

Purcek, G., Karaman, I., Yapici, G. G., Al-Maharbi, M., Kuçukomeroglu, T. & Saray, O., Apr 2007, In : International Journal of Materials Research. 98, 4, p. 332-338 7 p.

Research output: Contribution to journalArticle

wear resistance
Wear resistance
Extrusion
augmentation
cast alloys

Enhancement in mechanical behavior and wear resistance of severe plastically deformed two-phase Zn-Al alloys

Purcek, G., Karaman, I., Yapici, G. G., Al-Maharbi, M., Kuçukomeroglu, T. & Saray, O., Apr 1 2007, In : Zeitschrift fuer Metallkunde/Materials Research and Advanced Techniques. 98, 4, p. 332-338 7 p.

Research output: Contribution to journalArticle

wear resistance
Wear resistance
Extrusion
augmentation
cast alloys